2010
1. All cars must be 4 Cylinder non-turbo charged front whell drive American or foreign stock passanger cars. No pick up trucks, jeeps, or convertibles permitted. No two seated cars. Cars must have full solid steel roof. Spoilers, Wind Deflectors, etc. are permitted at a maximum of 5 inches tall. NO SAIL PANELS. Bodies must remain stock. Wheels may only be a maximum of 6 in. wide, steel only. MUST HAVE FULL SCREEN CAGE TO CAGE WITH 2 UPRIGHTS MADE OF AT LEAST 1/8X1 INCHES BAND IRON.
2. INTERIOR of cars must be gutted of all combustible materials. All carpeting, doors and quarter trim panels, headliners, and all seats must be removed. The dash may remain. Original vin plate must be in OEM location. Drivers seat must have at least a 5-point racing harness and must be securely fastened to frame or cage in good condition. A four point roll cage is mandatory with at least two driver side door bars with two uprights between each vertical bar, and one door bar on passenger side. EVERY WELDED JOINT MUST BE COMPLETELY WELDED WITH GUSSETS. ALL FOUR "FLOOR" MOUNTING POINTS MUST HAVE AT LEAST A 6X6X1/4 IN. STEEL PLATED WELDED TO BAR, WITH GUSSETS, AND BOLTED AR LEAST FOUR 3/8 BOLTS (MIN OF GRADE 5) TO FLOOR. ANY CAGE THAT IS DEEMED UNSAFE BY THE TECH INSPECTORS WILL NOT BE PERMITTED TO RACE.
3. All doors must be welded with a minimum of two 1/8x1x6 steel flats welded along the body side or bolted with 1/8x3x6 steel flats with at least two 5/16 grade 5 bolts. Top of window frames to roof must be welded or bolted with one flat with given dimensions. Front and rear bumper systems must remain stock. No additional bracing or tubing behind bumpers permitted. No plating or bracing of bumper mounting brackets permitted. Bumper shocks must remain functional.
4. NO GLASS. Plastic trim must be removed from the outside of body. All headlights, taillights, marker lights, grills, mirrors, door handles, mud flaps, and any miscellaneous exterior plastic must be removed. NO ADDITIONAL CUTTING AWAY OR CUTTING DOWN ANY OF THE CARS BODY PERMITTED.
5. All suspension and steering parts must remain stock. No air ride or traction control. No beefing up or replacing of suspension or steering parts with heavy-duty parts. STOCK WHEELS ONLY. TIRES MUST BE STEEL BELTED RADIALS OF 60, 65, 70, 75 SERIES ONLY AND MUST CARRY DOT NUMBER. ALL TIRES MUST BE OF SAME SIZE. No Snowtires. No recaps, racing recaps or racing tires of any kind permitted. Grooving and Siping will be permitted.
6. NO ALL WHEEL DRIVE CARS.
7. All radiators, gas tanks and batteries must remain in stock location. No additional cooling systems permitted. Radiators must have an overflow catch can. Cars must run stock air cleaner assembly (K&N Filter allowed, NO Cold Air Type). Original gas tanks must remain in stock location, but if you want to use a fuel cell, it must be located in the trunk. Trunk floor must be stock. No lowering of fuel cells. Fuel cell must be held down by at least two 1/8x1 in. steel straps. Absolutely no homemade fuel cells permitted. If car comes stock with plastic tank, must have 1/8 skid plate of any type. (16 cauge steel plate or 1/8 inch alluminum.)
8. Cars must have a minimum 18 in. high number painted on both front doors and roof. They must be painted with a contrasting color.
9. All cars must have an approved fully charged fire extinguisher accessable. ABC ONLY!
10. Stock hood latch must be removed and replaced with at least 2 hood pins. You may install one bar in front of the radiator with supports not extending past front of strut tower. (may not tie into four point cage).
11. No DOHC V-Tec. If running a V-Tec must 1.6 L SOHC.
12. No welded or locked rears.
13. Any over competitve cars will be slowed down by track.
*Subject to Change.